Cap, FPT PVC Schedule 40 3/4" (448-007)

This 3/4" Schedule 40 PVC Threaded Cap (FPT) provides a clean, pressure-rated closure for any standard 3/4" male NPT-threaded pipe end, nipple, or fitting outlet in commercial and light industrial piping systems. Constructed in white Schedule 40 PVC, it offers the corrosion resistance and chemical compatibility required across a wide range of fluid handling applications where a 3/4" male-threaded port must be sealed reliably — whether for permanent closure, phased construction, pressure testing, or future system expansion — without the added cost or weight of a metal cap.

The single female pipe thread (FPT) interior is cut to NPT tapered thread standards, threading directly onto any 3/4" male NPT pipe end or nipple to form a pressure-tight mechanical closure when made up with thread sealant or PTFE tape. As a terminal fitting, the threaded cap is the standard solution for closing unused branch outlets at male-threaded nipple stubs, capping system test points between pressure tests, sealing spare ports on manifolds and valve bodies at male-threaded connections, and terminating dead-end threaded lines during phased system construction or expansion. The FPT cap threads over a male pipe end — it should not be confused with the MPT plug (450-007 confirmed in this catalog session), which threads into a female port rather than over a male end; the spigot plug (449-007 confirmed in this session), which cements permanently into a socket fitting hub rather than threading over a pipe end; or the slip cap (447 series, 3/4" if stocked), which sockets over a pipe end and is solvent-cemented in place for a permanent bond. At 3/4", this is the highest-demand entry in the 448 series — appearing at male-threaded nipple stubs throughout all-threaded residential and light commercial irrigation valve station assemblies, solenoid valve outlet stubs, riser extension assemblies, pump station valve body male-threaded connections, and zone header distribution manifold male-threaded terminations where 3/4" is the dominant all-threaded PVC assembly diameter and spare male-threaded pipe ends require reliable closure during construction, testing, and staged expansion phases. The threaded construction allows the cap to be removed and reinstalled without cutting into the assembly — a practical advantage over permanent solvent-cement closures wherever future port access is anticipated at 3/4" male-threaded stub ends throughout the valve station and distribution assembly.

Rated to approximately 480 psi at 73°F, this cap is suited for standard commercial and light industrial water distribution and irrigation service within its pressure class. Its PVC composition provides excellent resistance to corrosion, scale, chlorinated water, and a broad range of chemical exposures — including resistance to seizing onto male threads over time, making it a more maintainable long-term closure than metal caps in moisture-prone or chemically active environments. NSF/ANSI 61 listing confirms suitability for potable water contact.

Install using a quality pipe thread sealant or PTFE tape on the male NPT threads before engagement. Avoid over-torquing — PVC threads require hand-tight plus one to two turns; excessive force can crack the fitting or distort thread engagement. If used as a temporary test cap, inspect the fitting and threads before returning to service. Derate pressure ratings for elevated temperatures per published derating curves.

Specifications:

Industries & Applications:

• Irrigation & Water Distribution — Seals unused or temporarily inactive 3/4" male NPT pipe ends, nipple stubs, riser extension stubs, and manifold outlet male-threaded connections throughout residential and light commercial all-threaded PVC irrigation valve station assemblies, zone header distribution manifolds, and pump station valve body male-threaded connections where 3/4" is the dominant all-threaded assembly diameter and spare male-threaded ports require reliable removable closure during phased installation or future zone expansion
• Commercial Plumbing — Caps 3/4" male NPT pipe ends and nipple stubs on pressurized supply systems, distribution manifolds, and branch supply assemblies in commercial building water systems during construction phasing, pressure testing, or permanent closure of unused male-threaded branch connections at the widely specified 3/4" branch supply diameter
• Pump Station Assemblies — Caps spare male-threaded ports on 3/4" pump station valve bodies, manifold assembly male-threaded outlets, bypass line stubs, and distribution header male-threaded terminations where unused ports must be sealed during initial installation and may be reactivated during future system modifications without cutting into the assembly
• Industrial Process Piping — Closes unused 3/4" male-threaded branch outlets, spare manifold ports, and dead-end test points on all-threaded process water headers and distribution assemblies in water treatment, chemical processing, and manufacturing facilities where the cap provides both a pressure test closure and a reconfigurable future tap point at the 3/4" service branch diameter
• Water Treatment & Aquaculture — Used to seal spare 3/4" male-threaded ports on filter manifold stubs, pump station valve body outlets, treatment equipment assemblies, and chemical dosing distribution connections where NSF/ANSI 61 compliance and long-term chemical resistance are required at each sealed 3/4" male-threaded port with future access anticipated during system maintenance or expansion
• HVAC & Mechanical Systems — Caps unused 3/4" male-threaded ports on cooling tower supply valve assemblies, chilled water distribution manifold male-threaded stubs, and chemically treated water system service assemblies within the Schedule 40 pressure rating class where future access to sealed ports may be needed during seasonal maintenance or system modifications